SMD Form Power Inductor -SGT | GUTE BESSERUNG
SMD Molding Netzdrossel-Funktion & Merkmal:
◆ hohe Strombelastbarkeit
◆ Hochfrequenzbereich bis zu 5 MHz
◆ sehr niedriger DC-Widerstand
◆ geschirmten Aufbau
◆ geringes Rauschen
◆ Ultra-Low-Cost
◆ RoHS-konform
Anwendung:
◆ PDA / Notebook / Desktop / Server-Anwendungen
◆ DC / DC ComVerter
◆ Induktor for general purpose use
Inductor SMD-Datenblatt
| Artikelnummer | A (mm) | B (mm) | C (mm) | D (mm) | E (mm) | SPQ | |||||||
| 0312 | 3,50 ± 0,20 | 3,2 ± 0,20 | 1,00 ± 0,20 | 0,70 ± 0,20 | 1,20 ± 0,20 | 4K | |||||||
| 0302 | 3,50 ± 0,20 | 3,2 ± 0,20 | 1,80 ± 0,20 | 0,70 ± 0,20 | 1,20 ± 0,20 | 3K | |||||||
| 0412 | 4.45 ± 0.25 | 4,06 ± 0,25 | 1,00 ± 0,20 | 0.76 ± 0.30 | 2,00 ± 0,20 | 3K | |||||||
| 0402 | 4.45 ± 0.25 | 4,06 ± 0,25 | 1,80 ± 0,20 | 0.76 ± 0.30 | 2,00 ± 0,20 | 4K | |||||||
| 0512 | 5.70 ± 0.30 | 5,20 ± 0,20 | 1,00 ± 0,20 | 1.10 ± 0.30 | 2,50 ± 0,30 | 3K | |||||||
| 0515 | 5.70 ± 0.30 | 5,20 ± 0,20 | 1,30 ± 0,20 | 1.10 ± 0.30 | 2,50 ± 0,30 | 3,5K | |||||||
| 0518 | 5.70 ± 0.30 | 5,20 ± 0,20 | 1,60 ± 0,20 | 1.10 ± 0.30 | 2,50 ± 0,30 | 3K | |||||||
| 0612 | 7.00 ± 0.30 | 6.60 ± 0.30 | 1,00 ± 0,20 | 1,8 ± 0,30 | 3,00 ± 0,30 | 3K | |||||||
| 0615 | 7.00 ± 0.30 | 6.60 ± 0.30 | 1,30 ± 0,20 | 1,8 ± 0,30 | 3,00 ± 0,30 | 2K | |||||||
| 0618 | 7.00 ± 0.30 | 6.60 ± 0.30 | 1,60 ± 0,20 | 1,8 ± 0,30 | 3,00 ± 0,30 | 1,5K | |||||||
| 0602 | 7.00 ± 0.30 | 6.60 ± 0.30 | 1,80 ± 0,20 | 1,8 ± 0,30 | 3,00 ± 0,30 | 1,5K | |||||||
| 0624 | 7.00 ± 0.30 | 6.60 ± 0.30 | 2,20 ± 0,20 | 1,8 ± 0,30 | 3,00 ± 0,30 | 0,5K | |||||||
| 0603 | 7.30 ± 0.30 | 6.60 ± 0.30 | 2,80 ± 0,20 | 1,8 ± 0,30 | 3,00 ± 0,30 | 0,5K | |||||||
| 0605 | 7.30 ± 0.30 | 6.60 ± 0.30 | 4,80 ± 0,20 | 1,8 ± 0,30 | 3,00 ± 0,30 | 0,5K | |||||||
| 1004 | 11,00 ± 0,50 | 10,00 ± 0,30 | 3,80 ± 0,20 | 2,3 ± 0,30 | 3,00 ± 0,30 | 0,5K | |||||||
| 1005 | 11,00 ± 0,50 | 10,00 ± 0,30 | 4,80 ± 0,20 | 2,3 ± 0,30 | 3,00 ± 0,30 | 0,5K | |||||||
| 1235 | 13.50 ± 0.50 | 12.50 ± 0.30 | 3,30 ± 0,20 | 2,3 ± 0,30 | 4.70 ± 0.30 | 0,5K | |||||||
| 1205 | 13.50 ± 0.50 | 12.50 ± 0.30 | 4,80 ± 0,20 | 2,3 ± 0,30 | 4.70 ± 0.30 | 0,5K | |||||||
| 1206 | 13.50 ± 0.50 | 12.50 ± 0.30 | 5.70 ± 0.30 | 2,3 ± 0,30 | 4.70 ± 0.30 | 0,5K | |||||||
| 1265 | 13.50 ± 0.50 | 12.50 ± 0.30 | 6.20 ± 0.30 | 2,3 ± 0,30 | 4.70 ± 0.30 | 0,5K | |||||||
| 1707 | 17,60 ± 0,40 | 16.90 ± 0.30 | 6.70 ± 0.30 | 2.10 ± 0.30 | 11.90 ± 0.30 | 0,3K | |||||||
| Molding Typ Power Inductor TMPC0312H Serie |
|||||||||||||
| Artikelnummer | Induktivitätswert L0 (uh) | I rms (A) typ. | Ich saß (A) typ. | DCR (MQ) typ. @ 25 ℃ | DCR (mQ) max. @ 25 ℃ | ||||||||
| TMPC0312H-R47MG | 0,47 ± 20% | 5.00 | 7,20 | 25 | 30 | ||||||||
| TMPC0312H-R56MG | 0,56 ± 20% | 4.50 | 6.60 | 31 | 36 | ||||||||
| TMPC0312H-R68MG | 0,68 ± 20% | 4.00 | 6.10 | 34 | 40 | ||||||||
| TMPC0312H-R82MG | 0,82 ± 20% | 3,50 | 5,80 | 41 | 48 | ||||||||
| TMPC0312H-1R0MG | 1,00 ± 20% | 3.30 | 5,50 | 50 | 60 | ||||||||
| TMPC0312H-1R5MG | 1,50 ± 20% | 3,00 | 4.00 | 71 | 85 | ||||||||
| TMPC0312H-2R2MG | 2,20 ± 20% | 2,70 | 3.40 | 98 | 115 | ||||||||
| TMPC0312H-3R3MG | 3,30 ± 20% | 2.00 | 3.10 | 191 | 210 | ||||||||
| TMPC0312H-4R7MG | 4,70 ± 20% | 1,60 | 2,80 | 266 | 293 | ||||||||
| TMPC0312H-5R6MG | 5,60 ± 20% | 1,50 | 2.20 | 310 | 360 | ||||||||
| TMPC0312H-6R8MG | 6,80 ± 20% | 1,40 | 2.00 | 360 | 400 | ||||||||
| TMPC0312H-8R2MG | 8,20 ± 20% | 1,20 | 1,70 | 420 | 463 | ||||||||
| TMPC0312H-100MG | 10,0 ± 20% | 1,00 | 1,40 | 498 | 550 | ||||||||
| Molding Typ Power Inductor TMPC0302H Serie |
|||||||||||||
| Artikelnummer | Induktivitätswert L0 (uh) | I rms (A) typ. | Ich saß (A) typ. | DCR (MQ) typ. @ 25 ℃ | DCR (mQ) max. @ 25 ℃ | ||||||||
| TMPC0302H-R10YG | 0,10 ± 30% | 10.50 | 14.00 Uhr | 6.6 | 9 | ||||||||
| TMPC0302H-R47MG | 0,47 ± 20% | 7.00 | 9.00 | 19.7 | 23 | ||||||||
| TMPC0302H-R68MG | 0,68 ± 20% | 5,50 | 7.00 | 25.5 | 29 | ||||||||
| TMPC0302H-1R0MG | 1,00 ± 20% | 4.00 | 5.00 | 32.0 | 38 | ||||||||
| TMPC0302H-2R2MG | 2,20 ± 20% | 3,50 | 3,70 | 65,0 | 75 | ||||||||
| TMPC0302H-3R3MG | 3,30 ± 20% | 3,00 | 3,50 | 125,0 | 145 | ||||||||
| TMPC0302H-4R7MG | 4,70 ± 20% | 2,60 | 3,00 | 172,0 | 200 | ||||||||
| TMPC0302H-5R6MG | 5,60 ± 20% | 2.20 | 2,60 | 205,0 | 238 | ||||||||
| TMPC0302H-6R8MG | 6,80 ± 20% | 1,90 | 2.20 | 260,0 | 300 | ||||||||
| TMPC0302H-100MG | 10,0 ± 20% | 1,40 | 1,60 | 366,0 | 422 | ||||||||
| Molding Typ Power Inductor TMPC0402HP Serie |
|||||||||||||
| Artikelnummer | Induktivitätswert L0 (uH) ± 20% | I rms (A) typ. | Ich saß (A) typ. | DCR (MQ) typ. @ 25 ℃ | DCR (mQ) max. @ 25 ℃ | ||||||||
| TMPC0402HP-R33MG-Z02 | 0,33 | 10.00 | 18.00 Uhr | 7.8 | 8.6 | ||||||||
| TMPC0402HP-R47MG-Z02 | 0,47 | 8.00 | 12.00 Uhr | 11.2 | 14 | ||||||||
| TMPC0402HP-R68MG-Z02 | 0,68 | 7.00 | 10.00 | 16.0 | 19 | ||||||||
| TMPC0402HP-1R0MG-Z02 | 1,00 | 5.00 | 8,50 | 22.0 | 27 | ||||||||
| TMPC0402HP-2R2MG-Z02 | 2.20 | 4.00 | 6.00 | 51.0 | 61 | ||||||||
| TMPC0402HP-3R3MG-Z02 | 3.30 | 3,50 | 4.00 | 69,0 | 76 | ||||||||
| TMPC0402HP-4R7MG-Z02 | 4,70 | 2,60 | 3,50 | 95,0 | 105 | ||||||||
| TMPC0402HP-6R8MG-Z02 | 6,80 | 2.10 | 2,80 | 150,0 | 172 | ||||||||
| TMPC0402HP-100MG-Z02 | 10.00 | 1,80 | 2,30 | 215,0 | 243 | ||||||||
| TMPC0402HP-220mg-Z02 | 22.00 Uhr | 1,20 | 1,40 | 470,0 | 500 | ||||||||
| Molding Typ Power Inductor TMPC0512HP Serie |
|||||||||||||
| Artikelnummer | Induktivitätswert L0 (uH) ± 20% | I rms (A) typ. | Ich saß (A) typ. | DCR (MQ) typ. @ 25 ℃ | DCR (mQ) max. @ 25 ℃ | ||||||||
| TMPC0512HP-R10YG-D | 0,10 ± 30% | 14.00 Uhr | 14.50 | 4.3 | 5.2 | ||||||||
| TMPC0512HP-R47MG-D | 0,47 | 7.00 | 11.00 Uhr | 13.6 | 15.8 | ||||||||
| TMPC0512HP-R68MG-D | 0,68 | 6.00 | 9.00 | 21.5 | 24.5 | ||||||||
| TMPC0512HP-1R0MG-D | 1,00 | 5.00 | 6.00 | 26.0 | 30 | ||||||||
| TMPC0512HP-2R2MG-D | 2.20 | 3,50 | 4.00 | 65,0 | 75 | ||||||||
| TMPC0512HP-3R3MG-D | 3.30 | 3,00 | 3,80 | 75,0 | 86 | ||||||||
| TMPC0512HP-4R7MG-D | 4,70 | 2,50 | 3.20 | 100,0 | 115 | ||||||||
| TMPC0512HP-5R6MG-D | 5,60 | 2.40 | 3.20 | 175,0 | 201 | ||||||||
| TMPC0512HP-6R8MG-D | 6,80 | 2.00 | 3,00 | 193,0 | 222 | ||||||||
| TMPC0512HP-100MG-D | 10.00 | 1,50 | 1,80 | 335,0 | 385 | ||||||||
| Molding Typ Power Inductor TMPC0602H Serie |
|||||||||||||
| Artikelnummer | Induktivitätswert L0 (uH) ± 20% | I rms (A) typ. | Ich saß (A) typ. | DCR (MQ) typ. @ 25 ℃ | DCR (mQ) max. @ 25 ℃ | ||||||||
| TMPC0602H-R10YG-D | 0,10 ± 30% | 14.00 Uhr | 14.50 | 4.3 | 5.2 | ||||||||
| TMPC0602H-R10YG-D | 0,47 | 7.00 | 11.00 Uhr | 13.6 | 15.8 | ||||||||
| TMPC0602H-R10YG-D | 0,68 | 6.00 | 9.00 | 21.5 | 24.5 | ||||||||
| TMPC0602H-R10YG-D | 1,00 | 5.00 | 6.00 | 26.0 | 30 | ||||||||
| TMPC0602H-R10YG-D | 2.20 | 3,50 | 4.00 | 65,0 | 75 | ||||||||
| TMPC0602H-R10YG-D | 3.30 | 3,00 | 3,80 | 75,0 | 86 | ||||||||
| TMPC0602H-R10YG-D | 4,70 | 2,50 | 3.20 | 100,0 | 115 | ||||||||
| TMPC0602H-R10YG-D | 5,60 | 2.40 | 3.20 | 175,0 | 201 | ||||||||
| TMPC0602H-R10YG-D | 6,80 | 2.00 | 3,00 | 193,0 | 222 | ||||||||
| TMPC0602H-R10YG-D | 10.00 | 1,50 | 1,80 | 335,0 | 385 | ||||||||
| TMPC0602H-220mg-D | 22.00 Uhr | 1,50 | 2,50 | 236,0 | 280 | ||||||||
| Molding Typ Power Inductor TMPC0605H Serie |
|||||||||||||
| Artikelnummer | Induktivitätswert L0 (uH) ± 20% | I rms (A) typ. | Ich saß (A) typ. | DCR (MQ) typ. @ 25 ℃ | DCR (mQ) max. @ 25 ℃ | ||||||||
| TMPC0605H-R33MG-D | 0,33 | 25.00 | 32.00 | 2.5 | 3 | ||||||||
| TMPC0605H-R47MG-D | 0,47 | 22.00 Uhr | 30.00 | 3.5 | 3.9 | ||||||||
| TMPC0605H-R68MG-D | 0,68 | 18.00 Uhr | 24.00 Uhr | 4.0 | 4.5 | ||||||||
| TMPC0605H-1R0MG-D | 1,00 | 15.00 Uhr | 20.00 Uhr | 6.1 | 6.5 | ||||||||
| TMPC0605H-2R2MG-D | 2.20 | 10.00 | 14.00 Uhr | 11.2 | 12 | ||||||||
| TMPC0605H-3R3MG-D | 3.30 | 8.00 | 12.00 Uhr | 19.0 | 20.9 | ||||||||
| TMPC0605H-4R7MG-D | 4,70 | 6.50 | 10.00 | 28.0 | 30.8 | ||||||||
| TMPC0605H-5R6MG-D | 5,60 | 6.00 | 9.00 | 43,5 | 49 | ||||||||
| TMPC0605H-6R8MG-D | 6,80 | 5,50 | 8,50 | 46.0 | 51.5 | ||||||||
| TMPC0605H-100MG-D | 10.00 | 4.00 | 7.50 | 60.0 | 69 | ||||||||
| TMPC0605H-220mg-D | 22.00 Uhr | 2,50 | 5,50 | 140,0 | 170 | ||||||||
| Molding Typ Power Inductor TMPC1004H Serie |
|||||||||||||
| Artikelnummer | Induktivitätswert L0 (uH) ± 20% | I rms (A) typ. | Ich saß (A) typ. | DCR (MQ) typ. @ 25 ℃ | DCR (mQ) max. @ 25 ℃ | ||||||||
| TMPC1004H-R15YG-D | 0,15 ± 30% | 43.00 | 75,00 | 0,5 | 0,6 | ||||||||
| TMPC1004H-R47MG-D | 0,47 | 28.00 | 43.00 | 1.3 | 1.5 | ||||||||
| TMPC1004H-R68MG-D | 0,68 | 22.00 Uhr | 39.00 | 2.4 | 2.7 | ||||||||
| TMPC1004H-1R0MG-D | 1,00 | 18.00 Uhr | 36.00 | 3.0 | 3.3 | ||||||||
| TMPC1004H-2R2MG-D | 2.20 | 12.00 Uhr | 27,00 | 6.5 | 7 | ||||||||
| TMPC1004H-3R3MG-D | 3.30 | 11.00 Uhr | 20.00 Uhr | 10.8 | 11.8 | ||||||||
| TMPC1004H-4R7MG-D | 4,70 | 10.00 | 17.00 Uhr | 15,0 | 15.5 | ||||||||
| TMPC1004H-5R6MG-D | 5,60 | 9.00 | 14.00 Uhr | 17.0 | 19.3 | ||||||||
| TMPC1004H-6R8MG-D | 6,80 | 8,50 | 13.50 | 17.5 | 23.3 | ||||||||
| TMPC1004H-8R2MG-D | 8,20 | 8.00 | 12.50 | 20,0 | 22.5 | ||||||||
| TMPC1004H-100MG-D | 10.00 | 7.50 | 12.00 Uhr | 27.0 | 30 | ||||||||
| TMPC1004H-200MG-D | 22.00 Uhr | 5.00 | 7.00 | 64.0 | 74 | ||||||||
|
|||||||||||||
Anmerkung:
Spezielle Anfragen neben den oben häufigsten verwendeten Typen können auf Ihrer Anforderung erfüllt werden.
150uH smd Induktor
SMD Molding Netzdrossel
Die Leute fragen auch:
1. Was sind die Vorteile von Chip-Induktivitäten?
2. Der Unterschied zwischen Induktor und gewöhnlichem Induktor
3. Übersicht der Induktivitätseigenschaften
4. Ausfallursachen der Patch-Leistungsinduktivität
5. Wählen Sie die geeignete Induktivität zum Schalten der Stromversorgung
6. The influence of the number of differential mode inductors
